The new generation of Ethernet Speed Certification
• From 100 Mb/s to 10 Gb/s
• Copper and fiber testing
• Performs 3 tests in one (SNR, BERT and Delay Skew)
Test for highest network speeds with your qualifier
Order number: NX_XGSE_10G
The new NetXpert XG verifies, if cabling channels support maximum transmission rates of up to 10Gb/s, irrespective of the category of cables, patch panels, or outlets installed. NetXpert XG provides a precise statement by automatically performing three individual tests which are combined into an overall test result.
New standards defining data rates up to 10Gb/s are a big challenge for the qualifiers of the latest generation. In order to verify if the cabling installed is able to support the increased data rates, operators need to perform adequate testing before commissioning the network, to avoid any unpleasant surprises. NetXpert XG enables you to meet the new challenges now!
The Secure Edition ensures NetXpert XG can also be used in restrictive environments where Wi-Fi or WLAN detection enabled devices are prohibited.
LiveLight™: Trend display of optical transmission loss in real time
Endurance test to detect contact problems on fiber optic connectors
-
With LiveLight™ the NetXpert XG-PLUS supports a worldwide unique function for measuring the power loss in fiber optic cables.
-
This aspect plays an extremely important role in troubleshooting. LiveLight™ offers the possibility, after replacing the plug connections or cables, to read the effect in real time on the LiveLight ™ trend diagram.
-
This procedure is particularly helpful when eliminating intermittent faults, because in practice many problems can be traced back to the connectors.
Bit Error Rate test, Signal-to-noise ratio and Delay Skew
By performing a Bit Error Rate Test (BERT) and standardsbased tests as per IEEE 802.3an the NetXpert XG verifies the error-free data transmission up to 10Gb/s. The tests include further parameters that can impact a Gigabit transmission, such as signal-to-noise ratio (SNR) and delay skew. Delay skew indicates the signal time delay between the wire pairs used. Excessive delay can result in a serious degradation of transmission performance, making it impossible for the receiver to interpret the data stream correctly. Delay skew, just as the signal-to-noise ratio, are considered to be crucial parameters for a reliable data transmission.
User-friendly operation
Continuity test results of all 8 wires and the shielding are displayed in wire map format in full color, while showing cable faults such as opens, shorts, miswires, and split pairs in a clear and easy to understand way. NetXpert determines the cable length and the distance to faults performing full TDR (Time Domain Reflectometer) measurement in combination with a capacitance measurement, for increased accuracy.
Getting results faster
An autotest can be initiated either from the main unit or from the Active Remote, saving time spent for walking between outlets and reducing the overall working time.When troubleshooting, all cable tests can be performed individually, to minimize fault-finding time.
High-resolution 7-inch touch screen
The large high-resolution touch screen display facilitates work
not only in daylight but also in poor lighting conditions, while
the 7" touch screen provides sufficient space to ensure excellent
readability of the displayed test results.
Ruggedized casing with hanging straps
Equipped with hanging straps at both sides, the NetXpert XG allows for one-handed use, leaving the right/left hand free to connect the NetXpert XG to the next cabling channel under test.
Troubleshooting of active PoE++ networks
For the troubleshooting of active PoE++ networks, NetXpert XG additionally offers a comprehensive tool set. This includes load tests for voltage drop to verify stability of PoE supplies, identification of the devices connected to the network, and detection of availability of priority devices. NetXpert XG offers sufficient internal storage even for large projects and, if required, generates complete standardsbased measurement reports containing all the necessary test information. Extensive accessories turn the NetXpert XG into the ultimate multitool – from locating individual cables with the builtin tone generator or the Remote Identifiers, to generating measurement documentation and in-service troubleshooting of PoE++ networks.
Including ports for fiber optic measurements
The NetXpert offers full flexibility regardless of whether you are measuring fiber or copper cabling. Using its available SFP/SFP+ ports, various active fiber tests such as protocol detection (CDP/ LLDP), network ping test and network discovery can be performed. In the area of passive tests, qualification of fiber optic cabling will be possible by connecting one main unit at each end. To obtain high-quality test results, it is recommended to use SFPs tested by Softing IT Networks for active and passive tests.
Well-equipped for the challenges of the future
NetXpert XG ensures a future-proof start into the new era of high-speed qualification. The NetXpert series offers simple firmware upgrades, and a license system allows for later upgrades to add new features. There are 3 options (NetXpert 1G, NetXpert 2.5/5G and NetXpert XG). The purchase of an upgrade license always extends the functionality of the device one step upwards. All wear parts (e.g. RJ45 jack) can easily and conveniently be replaced.
Technical features at a glance
- Tests data cabling for IEEE 802.3 compliance at data rates
of up to 10 Gb/s (BERT) - Determines signal-to-noise ratio (SNR)
- Measures delay skew
- Combined length measurement performing TDR and capacitance measurements for highly accurate test results and easier troubleshooting even of shorts
- Full-color wire map shows opens, shorts, miswires, and split pairs in a clear and easy to understand way
- Saves test results and generates standards-based measurement reports providing „Pass/Fail“
Network and diagnosis
- Supports IPv4 and IPv6
- Discover your network and see the connected network devices
- Identifies defective PoE switches with a PoE load test
- DHCP test
- Ping lists can be defined and saved for later use
- LLDP/CDP detection and analysis
- Identifies VLANs present in your network
- Data transfer from the tester to the PC using USB stick
Documents
Delivery
Standard scope of delivery
WireXpert 500 Industrial Kit
- 1 WireXpert 500 Local - with cover, without measuring adapter
- 1 WireXpert 500 Remote- with cover, without measuring adapter
- 2 power supplies
- 2 power cables
- 2 headphones
- 1 Envelope with calibration certificate, USB stick, quick start guide
- 2 Industrial adapters
- 2 TERA to preLink® measuring cables
- 1 TERA-TERA cable 2 m
- 2 preLink® M12 D socket
- 2 preLink® M12 X socket
- 2 preLink® M12 D plug
- 2 preLink® M12 X connector
- 2 preLink® RJ45 socket
- 2 preLink® RJ45 plug
- 1 Hard case
- 2 plastic sorting boxes for preLink® plugs and sockets
Versions
Order number
| Versions | 1G | 2.5/5G | 10G | XGplus | ||||||||||||
| Part no | NX_XGSE_1G | NX_XGSE_25_5G | NX_XGSE_10G | NX_XGSE_Plus | ||||||||||||
| Max. speed | Active | Passive Qualification | Active | Passive Qualification | Active | Passive Qualification | Active | Passive Qualification | ||||||||
| 10Gbit/s | ---- | ---- | ---- | ---- | ---- | ---- | ---- | ---- | CU | FO | CU | ---- | CU | FO | FU | FO |
| 2.5/5Gbit/s | ---- | ---- | CU | CU | CU | CU | CU | CU | ||||||||
| 1Gbit/s | CU | FO | CU | ---- | CU | FO | FO | ---- | CU | FO | CU | ---- | CU | FO | CU | FO |
| CU = Copper, FO = Fiber Optic | ||||||||||||||||
All models can be upgraded with additional licenses.