|Length Measurement Technology|
Time-Domain Reflectometry (TDR) and capacitance
Cable Testing and ID: up to 1,000 ft (305 m)
|Power over Ethernet (PoE)|
Test supports IEEE 802.3af PoE (Type 1, max 15.4W),
Network and test support by interface:
Maximum voltage that can be applied to any 2 connector pins without causing damage to the tester:
|Save Test Results|
Stores unlimited cable or network tests with user defined names per project
Tone Frequencies: 730 Hz and 1440 Hz
English, German, French, Spanish
Li-Ion, 7.2 VDC, 3.1A-hr (typical)
Operating: 14 to 140° F (-10 to 60°C)
10 to 90% non-condensing
Injection molded plastic
7" Color TFT-LCD capacitive touch display,
245 x 177 x 73 mm (main unit)
|Weight with Battery|
1,2 kg (main unit)
The new NetXpert XG verifies, if cabling channels support maximum transmission rates of up to 10Gb/s, irrespective of the category of cables, patch panels, or outlets installed. NetXpert XG provides a precise statement by automatically performing three individual tests which are combined into an overall test result.
New standards defining data rates up to 10Gb/s are a big challenge for the qualifiers of the latest generation. Particularly cabling for wireless access points has to support the ever increasing data rates. In order to verify if the cabling installed is able to support the increased data rates, operators need to perform adequate testing before commissioning the network, to avoid any unpleasant surprises. NetXpert XG enables you to meet the new challenges now!
By performing a Bit Error Rate Test (BERT) and standardsbased tests as per IEEE 802.3an the NetXpert XG verifies the error-free data transmission up to 10Gb/s. The tests include further parameters that can impact a Gigabit transmission, such as signal-to-noise ratio (SNR) and delay skew. Delay skew indicates the signal time delay between the wire pairs used. Excessive delay can result in a serious degradation of transmission performance, making it impossible for the receiver to interpret the data stream correctly. Delay skew, just as the signal-to-noise ratio, are considered to be crucial parameters for a reliable data transmission.
Continuity test results of all 8 wires and the shielding are displayed in wire map format in full color, while showing cable faults such as opens, shorts, miswires, and split pairs in a clear and easy to understand way. NetXpert determines the cable length and the distance to faults performing full TDR (Time Domain Reflectometer) measurement in combination with a capacitance measurement, for increased accuracy.
Getting results faster
An autotest can be initiated either from the main unit or from the Active Remote, saving time spent for walking between outlets and reducing the overall working time.When troubleshooting, all cable tests can be performed individually, to minimize fault-finding time.
The large high-resolution touch screen display facilitates work
not only in daylight but also in poor lighting conditions, while
the 7" touch screen provides sufficient space to ensure excellent
readability of the displayed test results.
Ruggedized casing with hanging straps
Equipped with hanging straps at both sides, the NetXpert XG allows for one-handed use, leaving the right/left hand free to connect the NetXpert XG to the next cabling channel under test.
For the troubleshooting of active PoE++ networks, NetXpert XG additionally offers a comprehensive tool set. This includes load tests for voltage drop to verify stability of PoE supplies, identification of the devices connected to the network, and detection of availability of priority devices. NetXpert XG offers sufficient internal storage even for large projects and, if required, generates complete standardsbased measurement reports containing all the necessary test information. Extensive accessories turn the NetXpert XG into the ultimate multitool – from locating individual cables with the builtin tone generator or the Remote Identifiers, to generating measurement documentation and in-service troubleshooting of PoE++ networks.
The NetXpert offers full flexibility regardless of whether you are measuring fiber or copper cabling. Using its available SFP/SFP+ ports, various active fiber tests such as protocol detection (CDP/ LLDP), network ping test and network discovery can be performed. In the area of passive tests, qualification of fiber optic cabling will be possible by connecting one main unit at each end. To obtain high-quality test results, it is recommended to use SFPs tested by Softing IT Networks for active and passive tests.
NetXpert XG ensures a future-proof start into the new era of high-speed qualification. The NetXpert series offers simple firmware upgrades, and a license system allows for later upgrades to add new features. There are 3 options (NetXpert 1G, NetXpert 2.5/5G and NetXpert XG). The purchase of an upgrade license always extends the functionality of the device one step upwards. All wear parts (e.g. RJ45 jack) can easily and conveniently be replaced.
- Tests data cabling for IEEE 802.3 compliance at data rates
of up to 10 Gb/s (BERT)
- Determines signal-to-noise ratio (SNR)
- Measures delay skew
- Combined length measurement performing TDR and capacitance measurements for highly accurate test results and easier troubleshooting even of shorts
- Full-color wire map shows opens, shorts, miswires, and split pairs in a clear and easy to understand way
- Saves test results and generates standards-based measurement reports providing „Pass/Fail“
- Supports IPv4 and IPv6
- Discover your network and see the connected network devices
- Identifies defective PoE switches with a PoE load test
- DHCP test
- Ping lists can be defined and saved for later use
- LLDP/CDP detection and analysis
- Identifies VLANs present in your network
- Data transfer from the tester to the PC using USB stick
These SFP are recommended by Softing IT Networks for the use with the NetXpert XG:
Finisar FTLF8519P3BNL 1G(Multimode 1G)
Finisar FTLF1318P3BTL 1G(Single Mode 1G)
Finisar FTLX8574D3BCL 10G(Multimode 10G)
Finisar FTLX1475D3BCL 10G(Single Mode 10G)
1 x NetXpert Main Unit
1 x Active Remote
2 x Power supply
2 x Test cable
1 x Hard case
1 x Micro-USB adapter
+ 1 additional NetXpert XG main unit
+ 1 additional power supply
+ 4 LC/LC duplex patch cable
(Multimode OM4 and Singlemode OS2)