La batterie est peut-être déchargée. Branchez l'adaptateur AC et vérifiez que la batterie est en charge. Le LanExpert peut être chargé et utilisé simultanément.

Oui. Vous devez renvoyer votre appareil pour remplacer votre batterie. Veuillez nous contacter.

Sélectionnez l'icone "batterie" lorsque l'alimentation est de retour. Appuyez sur l'option "stay on" pour l'adaptateur secteur AC et la batterie. Si votre LanExpert ne s'allume toujours pas, veuillez brancher l'adaptateur secteur AC pour charger la batterie.

1000BASE-T requires that auto-negotiation establish a Master-Slave relationship between the two devices. Typically, a multi-port device (switch) will assume the role of Master and single-port devices (servers, end stations, etc.) will be the slave unit. The 1000BASE-T protocol has a means of arbitrating which device will assume a given role (master/slave). The purpose of this Master/Slave relationship is to determine which device will provide the clock for the link.

Select the down arrow on the scroll bar to view IP information including Port MAC, IP, Subnet, Gateway, DHCP, WINS, DNS1, DNS2, DNS3 addresses and Lease time (if using DHCP).

Make sure the LanExpert is linked to the network and that your DHCP Server is working properly. If using static IP, then make sure the IP information is entered into the Ports profile under setup.

The LanExpert uses UDP packets.

Sync the IP address to another LanExpert or the other port of the current LanExpert on the network to see Received packets, lost packets, seq error, duplicate packets and roundtrip time.

If both are flashing, the LanExpert is trying to connect to the network. If one LED stops flashing and is a solid color then that Port is connected.

See what configuration you are trying to connect with under Setup in PORTS. Inline and Independent mode needs both network cables connected to the LanExpert. The unit will not start collecting data until both of the ports have established a connection to the network.

SAVE - Capture is used to store the frames in the Frame Capture mode. Up to 1000 frames in each of 10 memory storage locations can be stored. Once stored the frames must be downloaded to the computer and viewed in the Wireshark protocol analysis software (this is a free software package go to www.wireshark.org to download the latest version).

This is very dependent on the design of the network but typically the tester would be placed on the backbone between the server and the switch this is the best location. Obviously if there are many servers, routers and switches, there is not one location that will see all of the traffic. A good location for looking at traffic going to and from the network would be on the network side of the main firewall appliance.

There are 49 user-configured profiles and one factory default. Factory default is not changable. The rest of the profiles are allowed to save settings related to different networks. This saves time so you only have to configure the setup once and not have to keep going back to change it.

Single ended mode is where the LanExpert is connected to one network device using either Port 1 or Port 2. Inline must have both ports connected to two network devices. This allows the LanExpert to inspect the traffic going through it. Independent mode is where each port on the LanExpert has its own IP and MAC address. This is used to look at two different ports on the network or to run a RFC 2544 stress test with one LanExpert.

Yes, use a profile other then Factory Default. Select Ping/ Trace under setup. Press the down arrow once and select an Edit button next to an Undefined list object enter in a name or a website. Please make sure a DNS server is running to resolve the name or website you have entered.

Yes, go to Setup under Ports and scroll down once to enter a VLAN tag that the LanExpert detects.

Question What is MAC cloning? Answer MAC cloning allows the LanExpert to simulate another network device by using its ( the device in question) MAC address to detect issues originating from that device.

Please make sure that the far end of the cable connected to the LanExpert is disconnected from the wiremap terminator or a network device.

The LanExpert only measures copper network cables (ie. CAT3, 5, 5e, 6 and 6e) that have a NVP of 65 to 74.

To measeure length plug one end of your cable into Port 2. Port 2 is marked on the LanExpert with a yellow outline. The other end of the cable should not be connected to anything. Make sure nothing is connected to Port 1 while making the measurement. Select start to measure the cable.

You can run the Stress Test using the two ports on one LanExpert. The Independent Mode must be selected to do the Stress Test with a single LanExpert. You can also conduct the Stress Test using two LanExperts. One unit is designated as the remote unit and both are set to the Single Ended Mode.

To conduct a test that meets 100% of the RF2544 requirements would take about 2.5 days of continuous testing. This is typically only done in a laboratory environment and rarely (if ever) done in the field. Field tests are almost always customized by the user to provide a thorough test within a more reasonable time frame. For example, the RFC2544 requires testing with eight different packet sizes. A typical field test will reduce the number of different packet sizes, many times only using the largest and smallest packet size, which greatly reduces the test time. The test times shown for each test on the LanExpert are for the default settings, which we have picked for field tests. As the user changes the test parameters these estimated times will change so that the total test time is known before the tests are started.

The battery pack may need to be charged. Attach the AC adapter and verify the battery pack is being charged. The LanExpert can be used at the same time the battery pack is being charged.

Yes, however it needs to be returned to the manufacture for replacement. Contact us for assistance.

Select the battery symbol when power is turned back on. Select "stay on" option for both AC power and battery power. Your LanExpert doesn’t turn on? Plug in the AC power to charge the battery.

The first time the unit is powered on or if the time is lost there are a series of four dashed lines in the center of the top edge of the display. Or if the time is not correct. Touch the dashes or the displayed time with the stylus or fingertip and the time and date set screen will appear. Adjust the time and/or date. Then touch the Exit button at the top right of the screen to go back to the previous screen.

No, any sharp pointed object will damage the touch screen. Contact us for replacement components.

Adjust the backlight brightness to a level that corrects this. Follow the Set Illumination Options in the Getting Stated section of the User Guide or in the LanExpert’s Setup section.

Hold down the power button for about 5 seconds to turn the unit off. Turn unit back on. Try to recreate the situation to see if the unit freezes again. If you can recreate the "freeze", please email Psiber the exact situation that made your LanExpert freeze and we will look into it.

Hold down the power button for about 5 seconds to turn the unit off. Turn unit back on. Please email us, if this happens multiple times, with the exact situation and we will look into it.

The Touch Screen may need to be aligned. Select Setup from the Home screen goto Touch Panel in the lower icon area. Perform alignment.